The internal and external corner is a professional term in decoration, which refers to the included angle between general wall and ceiling, concave internal corner, protruding external corner, and the included angle between external corner. The form is general wall and wall, and the line treatment method of internal and external corner is introduced in detail by Jinan putty factory as follows.

　　一、處理方法為陰陽線夾角法

　　1、 The treatment method is the angle between the internal and external lines1. 油漆

　　1. paint

　　當陰陽角繪畫漆要保證平整,因為這必須提前有彈性的線,當繪畫漆可以使用鋁合金來依靠一邊,另一邊吹刮,如果想要耐用,陽角可以進行刷涂白水泥和石膏粉。

　　When the painting paint of internal and external corners should be smooth, because it must have elastic lines in advance. When the painting paint can rely on one side and the other side for blowing, if it wants to be durable, the external corners can be brushed with white cement and gypsum powder.

　　2. 壁紙

　　2. wallpaper

　　當壁紙陰陽角是更容易出現問題,陽角紙可以使用刮刀小心墻上貼壁紙,用手的凸角直折向下,然后用壁紙刀切,加上良好的膠棒,可以處理內部角從壁紙的凹角平的,外部與刮板上下移動貼墻,再好的墻紙。

　　When the internal and external corners of the wallpaper are the most likely to cause problems, the external corner paper can be pasted on the wall carefully with a scraper. The convex corners of the hand can be folded straight down, and then cut with a wallpaper knife. With a good glue bar, the internal corners can be treated as flat from the central concave corners of the wallpaper. The external and scraper can be moved up and down to paste the wall, and then the good wallpaper can be pasted.

　　3.貼瓷磚

　　3. tiles

　　貼瓷磚時，墻面陰陽角處理是更困難的。更常見的方法是用瓷磚本身來拼接，瓷磚邊緣用切割機或手工切割成45度角，這樣貼出的角度更圓潤美觀。

　　When tiling, the treatment of internal and external corners of the wall is the most difficult. The more common method is to use the tile itself to splice, and the edge of the tile is cut into 45 degree angle with a cutting machine or by hand, so that the angle pasted out is more round and beautiful.

　　二、處理墻壁陰陽角度的注意事項:

　　2、 Precautions for dealing with the internal and external angles of the wall:

　　1. 批灰處理

　　1. Batch ash treatment

　　先對基層灰進行批量處理，然后用刮刀對反彈線進行刮削，使其與周圍的陰陽角和凸塊都干凈，避免出現反彈線不直的情況。

　　First, the base ash is treated in batches, and then the rebound line is scraped with a scraper to make it clean with the surrounding internal and external corners and bumps, so as to avoid the situation that the rebound line is not straight.

　　2. 彈性線處理

　　2. Elastic line treatment

　　在處理墻上的陰陽角線時，一定不能忽略彈性線。在每個垂直陰陽角,垂直線應該下降了的線彈性線治療,和一個平行的線平行的垂直線陰陽角應放置的位置500毫米雙方基于陰陽角的垂直線。墻面吹膩子前，用石膏對陰陽角兩側用500毫米內進行找平，找平誤差不超過2毫米為準確。

　　When dealing with the internal and external corners of the wall, elastic lines must not be ignored. In each vertical internal and external corner, the vertical line should be lowered by the linear elastic line treatment, and the internal and external corners of the vertical line parallel to a parallel line should be placed at 500mm based on the vertical line of the internal and external corners. Before puttying the wall, plaster the two sides of the internal and external corners within 500mm, and the leveling error shall not exceed 2mm.

　　3、刷膩子

　　3. Apply putty

　　沿著彈性線用膩子將陰陽角直,等干后打開滿是灰,然后由鋁合金統治者從陰角陽角,來來回回,為了避免陰角不直,陰陽角完成后注意檢查,一般在5毫米誤差是正常范圍,超過5毫米石膏找平處理。

　　Use putty to straighten the internal and external corners along the elastic line, open it to be full of ash after drying, and then the aluminum alloy ruler will come and go back from the internal and external corners. In order to avoid the internal and external corners are not straight, pay attention to the inspection after the completion of the internal and external corners. Generally, the 5mm error is the normal range, and the gypsum is more than 5mm for leveling.

　　4. 抗爆處理楊角

　　4. Anti explosion treatment of Yangjiao

　　墻面陰陽角線完成處理后做好保護,因為陽角是凸,所以更危險,注意抗爆陽角處理,可使陽角光滑,用砂紙打磨或安裝角的保護,這是一個很好的方式來保護陽角。

　　Protect the internal and external corners of the wall after finishing the treatment, because the external corners are convex, so it is more dangerous. Pay attention to the anti explosion external corners treatment, which can make the external corners smooth. Use sandpaper to polish or install the protection of the angle, which is a good way to protect the external corners.

　　以上是濟南膩子粉廠家為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.man5g.cnThe above is the relevant content introduced by Jinan putty powder manufacturer. To learn more, please visit the website: http://www.man5g.cn